Check out the coil wheel. Depending on where the rope broke, you might have some rope left on the coil wheel. You can feed the old rope back through its hole and retie the pull handle if you have enough rope to pull start the mower. Next, replace the housing and then screw it back in place.
Can you start a mower without the pull cord?
No, you can’t just use anything you find lying around.. it’s a specific type of cord, designed for a specific job. Put one end of the rope through the pull start handle and tie a knot big enough so that the rope can’t come through the hole in the handle.
How do you start a lawnmower with a pull cord?
Pull the starter cord.
If your lawnmower has a horizontal lever near the handle, hold it against the handle. Next, grip the handle of the starter (attached at the end of a rope or cord), and pull upward quickly and firmly. You may have to do this several times before the motor starts up.
What is the thing you pull to start a lawn mower called?
Rope start (also called pull start or rewind start) is a method of starting an internal combustion engine, usually on small machines, such as lawn mowers, chainsaws, ultralight aircraft, small outboard motors and portable engine-generators.
How do you start a lawn mower if your not strong enough?
The following are a few things you can do to easily start your mower if you can’t get your cord to pull hard enough:
- Check Out the Mower’s Parts. …
- Use Tools for Easier Pull. …
- Adjust the Height of the Lawn Mower. …
- If All Else Fails—Build Up Your Arm Muscles. …
- Check the Spark Plug. …
- Check the Valves. …
- Make Sure There’s Enough Gas.
Why wont my lawn mower pull the string?
What if the starter rope won’t pull? The crankshaft is connected to the blade shaft on your recoil start walk behind lawn mower, so if the pull cord is stuck, it could be because something is blocking the movement of the blade. Disconnect the spark plug for safety, then take a look under the deck.
How much does it cost to fix a lawn mower pull cord?
The cost of a pull cord repair is $19.95 which includes the replacement rope.
How do I adjust the choke on my lawn mower?
How to Adjust the Choke on a Craftsman Lawn Mower
- Pull the choke adjustment knob on the dashboard out completely if the engine is cold.
- Start the engine.
- Push the choke knob in partially until the engine is running smoothly.
- Continue to push the choke adjustment knob in slowly as the engine is warming up.
How do you make pull easier to pull?
To fix this problem it’s really simple. All you need to do is remove the spark plug and pull over the lawnmower using the starter rope with the spark plug removed. This will remove any excess oil and fuel from the piston area and also through the exhaust. You should now attempt to restart the lawnmower.
How does a pull start mower work?
The starting cord is wound around a spring-loaded hub that is designed to engage with the engine flywheel. When you pull the cord, the flywheel rotates, which in turn rotates the crankshaft and moves the piston. A magnetic coupling on the flywheel causes the spark plug to fire cyclically as the piston moves,.
How does a pull start mechanism work?
In the center of the pulley, a recoil spring connects to the pulley through a hook. When the starter rope gets pulled off the pulley and out of the engine, the recoil spring stretches out. When the operator lets go of the rope, the recoil spring snaps back and the rope recoils onto the pulley.
What could cause a lawn mower not to start?
Your Mower Won’t Start:
Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.
What does a bad spark plug look like lawn mower?
Its center electrode should have a flat top. If its top is rounded, then the spark plug must be replaced. Look for cracks or chips in the spark plug’s porcelain sheath as well as pitting on its firing electrode.