When traveling on a ramp with an unloaded forklift, always travel with the forks pointed downgrade, regardless of whether you are ascending or descending the ramp.
How do you drive a forklift on a ramp?
When going down a ramp, drive in reverse with the load and keep the forks pointed up the slope. When traveling without a load, the forks should always point down the slope. The forklift operator should also drive in reverse up the ramp or drive forward when going down the ramp.
When driving a forklift up a ramp without a load your forks should be pointing down the ramp?
When carrying a heavy load on grade, the forklift must be able to safely stop. When your operators are traveling without a load, the forks should be pointed down the incline. This would include going up or down the ramp. The forks should be raised enough to safely clear the grade.
Can a forklift be driven across a slope?
Slopes can make a forklift’s load to slide off, which can cause the lift to run the fallen load over. Plus, slopes can make a lift tip over forward, so the back wheels lift up. Other hazards include locked front wheels and spinning wheels, as both of these can cause a forklift spinning out of control.
When traveling with empty forklift the forks should be in what position?
When travelling in an empty forklift, the forks of the lift should be in the position of waist high.
Can a forklift go up a ramp?
A ramp, slope, or incline is defined as an angle that exceeds 10 percent. … Loaded forklifts must be driven with the load pointed up the ramp (good standard practice is to ALWAYS drive with the load pointed up the ramp or slope). Raise levels should be limited to the minimum height necessary for ground clearance.
When operating a loaded forklift going up a ramp you must?
Requirements and Recommended Practices:
- When traveling with a load, the load should point up the incline, regardless of direction of travel.
- Going up the incline: Drive forward. Forks pointed upgrade. Use a spotter if load blocks the driver’s view.
- Going down the incline: Drive in reverse. Turn head and face downgrade.
Can a pallet jack go up a ramp?
It should go without saying, but using a pallet jack on an incline is not usually advisable, according to the National Ag Safety Database. … If you do have to go up an incline, always make sure you’re pulling the jack. When going down a ramp, pushing is the only reasonable option.
What is the first thing you need to do before raising or lowering a load?
Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.
What class of forklift should not turn on an incline?
PEDESTRIANS AND FORKLIFTS SHOULD NEVER OCCUPY A RAMP OR INCLINE AT THE SAME TIME, IF THE OPERATOR OF A CLASS 1, 4, & 5 IS CARRYING A LOAD THAT BLOCKS THEIR FORWARD VISION ON LEVEL SURFACES, THEY ARE TAUGHT TO DRIVE IN REVERSE. BUT WHEN APPROACHING A RAMP OR INCLINE, THAT LOAD MUST FACE UPHILL.
Why is it dangerous to turn a forklift on a ramp or slope?
Not only can operators be at risk when travelling recklessly on slopes but the safety of pedestrians is also compromised. The load in which the forklift operator may be transporting can also be significantly damaged or even destroyed if safety precautions are not followed within this situation.
Should you jump off during a tipover?
Never jump off of a forklift. If the forklift is tipping over, do not attempt to jump off, because you could be pinned under the lift. If the forklift is tipping over, protect yourself by staying put: Stay in your seat and do not attempt to jump off.
Can a forklift tip over without a load?
Forklift Safety Rule Two: Don’t tip over. Many untrained operators assume that they can drive faster without a load, but look at the location of the CG with unloaded forks. … On the other hand a loaded forklift is more likely to tip forward with the CG now closer to the front axle.
What steps should you do every time you park a forklift?
Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.
How far should you stand from a forklift?
The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.
What will make the load more stable during travel?
When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.