What should you do every time you park a forklift?

Which step should you do every time you park a forklift?

Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.

Where should you not park a forklift truck?

Do not park an industrial lift truck near doorways, switches and electricity boards, fire fighting equipment, blind corners, on inclines, on soft ground, middle of an aisle, fire exits or pedestrian walk ways.

When operating a forklift what must you do?

Stay Safe While Using A Forklift

Ensure both forks are as far under the load as possible before lifting. Drive with the load as low as safely possible. Pay attention to posted speed limits and warning signs. Always look in the direction you’re traveling; if a load blocks the view ahead, travel in reverse.

IT IS INTERESTING:  How long does it take for forklift certification expire?

How should you normally drive your forklift?

To reduce these hazards, follow these requirements and recommendations:

  1. Always drive unloaded forklifts with the forks downgrade.
  2. Never drive a loaded forklift with the load downgrade.
  3. When driving up a ramp, drive loaded forklifts forward with the load upgrade.

13.06.2017

What should you check before lifting a load?

Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.

What accidents could occur when a forklift truck is parked?

Gravity is one of the biggest dangers to forklift operators. Parking on a ramp, incline, or on an uneven surface can cause the forklift to roll on its own. If the surface is steep enough, the vehicle’s parking brakes may not be enough to stop it from rolling.

Why are forklifts dangerous?

There are many factors that explain why forklifts are dangerous: Forklifts are heavy. … The weight of a forklift is unevenly distributed, which makes it harder to operate and drive. The rear wheels of a forklift are responsible for turning the vehicle, increasing the chances of tipping during tight turns.

How high should forks be when driving forklift?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back.

IT IS INTERESTING:  What does hoist mean in construction?

What happens when the load Centre is increased?

The weight capacity of a forklift attachment is tied to what is known as the Maximum Load Moment, which is when the load center distance increases, changing the weight distribution, and as a result, the amount of weight a truck can carry under those conditions.

What is the most important safety device on a forklift?

5 most important safety devices on a forklift

  1. Brakes. Brakes are the absolute most important safety feature on any motorized vehicle. …
  2. Seatbelts. …
  3. Overhead guards. …
  4. Lights. …
  5. Horn.

10.10.2018

What is the minimum safe distance to drive behind another forklift?

Falling distance of an object from a pallet or 15 feet, 5 Feet both sides, 5 Feet Rear of Forklift. do so (ALL CLEAR). Do not pass under the forks while in operation. in operation and a fix object.

What can you not do with a forklift?

Forklift operators should never:

  • Raise or lower loads while the forklift is moving and especially not while turning because it makes the forklift very unstable. …
  • Allow anyone to stand underneath or right next to raised forks. …
  • Carry a load with only one fork as it stresses the carriage.

Why do forklifts have 3 pedals?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. … That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

Is forklift driving hard?

Driving a forklift isn’t all cake, roses, and gas pedals. It’s going to be hard work. … Operating a forklift is considered a “hazardous occupation,” according to the Fair Labor Standards Act. As with any big machine, accidents happen.

IT IS INTERESTING:  Quick Answer: Does a forklift have the right of way?

Is it safe to drive a forklift backwards?

“It would be, in my opinion, a very dangerous way to drive a forklift for a long period of time,” Iunker said. Driving in reverse while looking backward would cause the steering wheel to move more than intended, making it very hard to control, he added.

Construction brigade