What should be done when operating a forklift?

What should not be done when operating a forklift?

Do not grab the overhead guard when traveling in reverse. Doing so could expose the operator’s finger to serious injury. Never turn on a grade or with the forks elevated. Do not carry passengers.

What should I check before operating a forklift?

Forklift Pre-Operation Checklist

  1. Fluid levels — oil, water, and hydraulic fluid.
  2. Leaks, cracks or any other visible defect including hydraulic hoses and mast chains. …
  3. Tire condition and pressure including cuts and gouges.
  4. Condition of the forks, including the top clip retaining pin and heel.
  5. Load backrest extension.

What should be considered when starting forklift operations and planning a task?

16 Simple Tips for operating a forklift safely

  • Operators must be qualified. …
  • Appropriate clothing must be worn. …
  • Examine Equipment before use. …
  • Starting up the forklift. …
  • Consider the surrounding environment. …
  • Operate at a safe speed. …
  • Avoid Hazards. …
  • Ensure your load is stable and secure.
IT IS INTERESTING:  What is a hoist and sling?

What is your duty of care while operating a forklift?

It is the companies responsibility to ensure the equipment staff are using is in safe and serviceable condition. Part of this Duty of care includes the operator inspecting the forklift prior to use. A checklist is one of the most common methods companies use to monitor and measure equipment serviceability.

What is the most important safety device on a forklift?

5 most important safety devices on a forklift

  1. Brakes. Brakes are the absolute most important safety feature on any motorized vehicle. …
  2. Seatbelts. …
  3. Overhead guards. …
  4. Lights. …
  5. Horn.

10.10.2018

Do and don’ts of forklift?

The 5 Dos and Don’ts of Forklift Safety

  • Do Drive Responsibly. Just like driving a car on the road, you should always operate your forklift at a speed that will allow you to stop safely. …
  • Don’t Go Over Your Forklift’s Load Capacity. …
  • Do Be Aware of Pedestrians. …
  • Don’t Skimp on Training. …
  • Do Maintain Your Forklift.

7.12.2015

What steps are done daily before using a forklift?

1) Conducting a visual check

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

What are 3 fluid levels that need to be checked before using the forklift?

Check of liquid Levels:

  • Hydraulic fluid.
  • Brake fluid.
  • Engine oil coolant.
  • Battery.
  • Fuel.

20.04.2011

What is a safe speed for a forklift?

The Material Handling Equipment Distributors Association (MHEDA) recommends a max speed of 8 mph in general and a 3 mph max speed in areas where pedestrians are present.

IT IS INTERESTING:  Frequent question: How can I speed up my Yale forklift?

What three guards are fitted to a forklift?

One final passive safety feature is the overhead guard. In the unlikely event that part of the load falls off of a raised pallet, the overhead guard is designed to protect the operator from small objects. The overhead guard is constructed to a very high standard and is an integral part of the forklift’s design.

What is the distance that I keep away from a forklift?

Pedestrian exclusion zones should be enforced within a three metre radius of a forklift. This distance should expand when the height of the forklift load or the speed travelled increases.

What steps should you do every time you park a forklift?

Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.

Why are forklifts so dangerous?

There are many factors that explain why forklifts are dangerous: … The load of a forklift is carried in the front of the vehicle, blocking the line of sight of the operator. Forklifts are frequently required to lift heavy loads to high places. Mistakes made during lifting can lead to serious injuries from falling loads.

Where can I not park a forklift?

Do not park an industrial lift truck near doorways, switches and electricity boards, fire fighting equipment, blind corners, on inclines, on soft ground, middle of an aisle, fire exits or pedestrian walk ways.

IT IS INTERESTING:  Frequent question: What is forklift machine?

What should you do if your forklift hits a powerline select the correct order?

Stay put. If your forklift hits a power line, the most important thing to remember is to stay in place. You will likely feel an instinctive need to get out of the vehicle and call for help, but it is absolutely imperative that you remain seated. Leaving the cab can result in electric shock.

Construction brigade