Quick Answer: What should you do if the forklift tips over?

If the forklift is tipping over, protect yourself by staying put: Stay in your seat and do not attempt to jump off. Lean away from the falling direction of the lift. Hold onto the steering wheel and make sure you’re stable.

What should you do if a forklift is tipping over?

In a forklift tip over, you should:

  1. remain seated and don’t lean out of the forklift.
  2. brace your feet, hold tight and lean away from the point of impact.

What would cause a forklift to tip over?

FORKLIFT TIP OVERS AND THEIR CAUSES

A longitudinal, or forward forklift tip over occurs when the center of gravity moves too far forward, which can happen when a lift is driven down a slope or ramp.

Is it difficult to tip over a forklift?

In every type of forklift, the rule is similar and simple – the equipment’s center of gravity should be inside the wheelbase. The center of gravity should stay in that position, it should not move forward or too far to any direction, otherwise, risk of tip over can happen.

IT IS INTERESTING:  Can a deaf person drive a forklift?

What steps should you take to improve stability and prevent a tip over?

Only stable or safely arranged loads must be handled!

  1. Keep the center of gravity low and avoid off-center loading. Off-center loads could cause tip-over or falling loads.
  2. Slowly operate the lift truck when picking up or placing a long or wide load, or when turning with such a load.

Why do forklifts not tip over?

At the back of every forklift is a counterweight. The size of this counterweight will depend on the capacity of the forklift. … The counterweight acts as a balance for the weight being lifted by the truck’s forks. As long as the center of gravity is inside the wheelbase for the vehicle, the forklift won’t tip over.

Where can I not park a forklift?

Do not park an industrial lift truck near doorways, switches and electricity boards, fire fighting equipment, blind corners, on inclines, on soft ground, middle of an aisle, fire exits or pedestrian walk ways.

Why is an unloaded forklift sometimes unstable?

Forklift stability is based on keeping the center of gravity inside what’s called the stability triangle. … When unloaded, the forklift’s center of gravity is right about here. When a load is added, the forklift’s center of gravity moves towards the forks. Heavier loads shift the center of gravity forward even further.

How do you drive a forklift uphill?

Avoid steep slopes. Make sure the load always points uphill. When going down a slope, be careful about the load falling off. Always drive with a lift “forks first” down a hill or slope (this puts more weight on the braking wheels, so the driver has more traction)

IT IS INTERESTING:  Should brakes be applied when using a passive hoist to lift a patient?

When setting a load What should you do first?

How should you raise the load?

  1. Check that the overhead clearance is adequate before raising loads.
  2. Do not raise or lower the fork unless the lift truck is stopped and braked.
  3. Lift loads straight up or tilt back slightly.

How should you carry an unbalanced load when one end is heavier?

If the load is unbalanced, keep the heavier end closer to you. Tilt the mast back. Lift the load and tilt it back a little more before traveling. Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground.

How low should forks be driving forklift?

When driving a forklift typically in a warehouse the forks should be above the ground at a height of 6 to 8 inches, approximately the same height that will go through a wooden pallet. If you scrape the floor surface, your forks are too low.

When may you lean out of the forklift?

Operators should never lean or reach outside of the cab, as this puts them at risk of contact with passing obstructions/vehicles. Rather than reach out to access something, they should stop their truck in a suitable place, make it safe, dismount and then access it on foot.

What are 3 contributing factors that can affect lift truck stability?

To help, we’ve highlighted four common causes, as well as some top tips that can be easily applied to reduce risk in each case.

  • Handling of suspended or live loads. …
  • Turning with an elevated load. …
  • Traversing a slope or uneven ground. …
  • Insecure loads or overloading. …
  • 01246 555222.
IT IS INTERESTING:  Question: Does a forklift count as heavy equipment?

11.04.2019

When preparing to move off the safest procedure is as follows?

MOVING OFF 10 Before moving off, look round and move only when you can do so safely. An easy way of remembering this is GOB which stands for Gears, Observations then Brakes.

What affects forklift stability?

The weight of the load on the forks. Positioning of the load. The weight of ballast (“counterbalance”) at the rear of the forklift. The surface of the floor (most forklifts are designed for level surfaces only)

Construction brigade