How do you use a forklift lever?

Use the lever on the right side of your steering column to raise or lower the tines to the load height. Note, Only adjust the height of the fork while the parking brake is activated and the forklift is in neutral. Make sure the load is stable and has a low center of gravity.

What do the levers do on a forklift?

Most forklifts have two levers to control the forks. The first lever controls the height of the forks. You pull back on the lever to make the forks go up, and you push forward to make the forks go down.

What are the 3 levers on a forklift?

A forklift’s directional controls help move the lift forward and backward. There are three forklift directional controls: park, drive, and reverse. Directional controls can be mounted to a lift’s steering column. Or, they may be placed in a position where an operator controls them with their foot.

How do you use a sit down forklift?

Make sure your forks are leveled off and close to the ground. Never travel with your forks more than 5-to-6 inches off the ground. Push in the clutch if it is a manual transmission, and put the transmission in “Forward.” Push down on the gas pedal and the forklift will move forward in drive.

IT IS INTERESTING:  How fast is a forklift?

Why do forklifts have 3 pedals?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. … That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

What is the inching pedal on a forklift?

The purpose of the inching pedal is to disengage the transmission without having to shift the gear lever into neutral every time a lift is performed. This pedal allows you to bring the forklift to a stop or to slow it down.

How do you control a forklift?

Make sure the truck is placed squarely in front of the load. Make sure the forks are at the correct height for lifting the load. Set the direction control to neutral. Never raise or lower the forks unless the forklift is stopped and the brake is set.

What is the most common cause of a forklift accident?

17 Sep The Most Common Forklift Accidents:

Now, the most common types of a forklift accident are when one overturns, when a worker is stuck, pinned-beneath, or crushed by a forklift, or when a worker falls from a forklift. An overturning forklift is a terrifying scenario.

What does plugging mean on a forklift?

What is forklift plugging? Plugging, also called regenerative braking, regen or switch-back, occurs when an operator traveling in one direction uses the directional selector to switch to the opposite direction.

Is forklift driving easy?

Just like an ordinary sedan car, a forklift can be fairly easy to operate. It only takes short time and little practice for you to get a grasp of it. But make no mistake, just because it is easy to operate, does it mean you will put your guard down. ALWAYS prioritize safety when driving a forklift.

IT IS INTERESTING:  Best answer: What is a capacity plate on a forklift?

What can you not do with a forklift?

Forklift operators should never:

  • Raise or lower loads while the forklift is moving and especially not while turning because it makes the forklift very unstable. …
  • Allow anyone to stand underneath or right next to raised forks. …
  • Carry a load with only one fork as it stresses the carriage.

Can you leave keys in a forklift?

Never leave an operating forklift unattended.

In fact, leaving keys in an unattended forklift (or, thus, leaving on the ignition of this vehicle) is illegal, and has dire consequences as a safety hazard, even without the actual occurrence of an accident.

How do I get my forklift to go forward?

Turn the key to start the forklift.

Locate the emergency brake lever on the left side of the machine and make sure it’s pulled down and activated. Put the key into the ignition on the right side of the steering column and turn it forward to start the forklift’s engine.

What is on a forklift test?

Your forklift test may include general knowledge of the truck. It has three main parts, the body, the overhead guard and the hydraulic lift.

How do you use a forklift for the first time?

6 Key Tips for Driving a Forklift for the First Time

  1. Dress Properly for the Job. First of all, you should make sure that you dress properly for the job. …
  2. Look it Over. Don’t just hop into the driver’s seat without taking a look at the forklift. …
  3. Clear the Area. …
  4. Get Comfortable. …
  5. Start Out Slow. …
  6. Keep Your Eyes Open.
IT IS INTERESTING:  How much does a forklift driver make at Amazon?

19.06.2017

Construction brigade