Best answer: Which of the following is a required step in properly parking a forklift?

When parking a forklift, slowly bring the vehicle to a stop, set the parking brake, turn off the ignition and remove the keys. If you are parking on an incline, turn the front wheels away from the downgrade so the forklift will not slide.

Which steps should you do every time you park a forklift?

Parking Safety Rules

  1. Always try to find a level surface to park on. …
  2. Lower forks, or the forklift attachment, all the way to the ground. …
  3. Put the gear into neutral.
  4. Make sure the wheels are straight. …
  5. Set the parking brake every time you park the forklift. …
  6. Turn off the engine before dismounting the forklift.

How do you park a forklift?

Forklift Parking Procedure

  1. Stop the forklift and apply the handbrake. …
  2. Fully lower the carriage and tynes.
  3. Tilt the mast forward so the tyne tips are touching the ground. …
  4. Turn the key or keyless switch to the ‘off’ position. …
  5. Release the units seatbelt and safely dismount from the operator cabin.
IT IS INTERESTING:  Frequent question: How do you get a forklift license in Ontario?

Where should you not park a forklift truck?

Do not park an industrial lift truck near doorways, switches and electricity boards, fire fighting equipment, blind corners, on inclines, on soft ground, middle of an aisle, fire exits or pedestrian walk ways.

When parking or leaving the forklift you must remove the ignition key?

Turn off the engine and the key should be removed

Aside from turning off the engine, and you know you will be away for a longer period, removing the key from the ignition and handing it over to your shift supervisor in case someone wants it to be used during that period is good practice as well.

When picking up a load the forks should be?

Carrying the load

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.

What is the most common type of forklift accident?

The most common type of lift truck accident is one of the most fatal: being crushed by a lift truck. The Centers for Disease Control and Prevention (CDC) says that most fatal lift truck accidents happen when a worker is crushed by a forklift overturns or falls from a loading dock.

What are the 3 pedals on a forklift for?

There are three types of forklift pedals: accelerator, brake, and clutch. A typical forklift has all three pedals present, but there are exceptions. For instance, some forklifts have an inching pedal that is used to disengage the lift’s transmission and slow down the machine or bring it to a complete stop.

IT IS INTERESTING:  Frequent question: Are scissor lifts considered powered industrial trucks?

What are the three major parts of a forklift?

The three major parts of a lift truck are the body (truck), overhead guard, and hydraulic lift.

Can you fail a forklift test?

Right from the start in 1969 there has never been a percentage score for the practical test of fork lift truck operator basic skills. There is for the written test but not for the practical. In fact it’s very simple. … If a trainee scores 41 or more they are deemed to have failed the test.

How many types of forklift are there?

Forklift Classifications

There are seven forklift classes outlined by the Occupational Safety and Health Administration (OSHA) that describe their fuel option and use.

Is forklift driving hard?

Driving a forklift isn’t all cake, roses, and gas pedals. It’s going to be hard work. … Operating a forklift is considered a “hazardous occupation,” according to the Fair Labor Standards Act. As with any big machine, accidents happen.

What accidents could occur when a forklift truck is parked?

Gravity is one of the biggest dangers to forklift operators. Parking on a ramp, incline, or on an uneven surface can cause the forklift to roll on its own. If the surface is steep enough, the vehicle’s parking brakes may not be enough to stop it from rolling.

How far should you stand from a forklift?

The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.

IT IS INTERESTING:  Best answer: How can I tell how many inches My truck is lifted?

Which steps must be done at least daily before using a forklift?

1) Conducting a visual check

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

Construction brigade